RAM Mounts

RoveSpec currently carries phone and tablet holders, C- and D-size marine electronics components, Tough-Claw bases, trolling-motor stabilizers, and fishing-rod holders. Selection begins with the device and environment, then proceeds through holder, ball size, arm length, adapter pattern, and mounting base.

RoveSpec’s current catalog includes B-size phone and tablet holders, C-size components and marine mounts, and D-size heavy marine components. RAM identifies B as a 1-inch ball, C as a 1.5-inch ball, and D as a 2.25-inch ball. Use the current RAM load guidance and the real vibration and leverage of the installation.

The arm provides articulation and clamping, but it does not correct an undersized ball family, unsupported mounting surface, or mismatched device pattern. Arm length changes reach and leverage. Round and rectangular plates differ by hole pattern and device interface, so compare the official drawing or stated compatibility.

RoveSpec carries X-Grip phone and tablet holders plus a Quick-Grip XL drill-down kit. “Universal” describes an adjustable range, not every device. Measure the device with its case and verify width, height, depth, buttons, camera, charging port, stylus, and any tether requirement on the exact RAM page.

RoveSpec carries small and medium Tough-Claw bases and stabilizer assemblies that use Tough-Claw. Rubber pads and a hand-tightened jaw create the grip; the clamp is not a permanent structural attachment and should be inspected for movement, surface damage, and interference before every trip.

RoveSpec carries C- and D-size marine mounts, including model-specific and universal plate configurations. A screen-size description is only a starting point. RAM’s ball-size guidance distinguishes standard and heavier marine applications, and longer arms increase leverage on the base.

RoveSpec carries Tough-Claw and strap-hose-clamp stabilizer configurations with different clamp ranges and arm lengths. Confirm that the motor can be deployed and stowed without binding, cables remain free, and the support cannot contact controls, rods, covers, or the hull.

RoveSpec carries bulkhead-base variants with different base mechanisms. Confirm the mounting surface, fasteners, rod-butt geometry, reel clearance, line path, removal motion, and whether the holder is intended for storage, transport, trolling, or active fishing.

• Measure phones and tablets with the installed case and accessories.
• Confirm the exact device hole pattern or use a holder whose stated range includes the device.
• Match B, C, or D ball size on both balls and the double-socket arm.
• Choose arm length only after checking leverage, vibration, line of sight, and control clearance.
• Verify clamp range or drill-down base pattern against the actual rail or surface.
• Confirm fastener material, backing, sealant, corrosion isolation, and structural support for marine installations.

RAM’s glossary explains common prefixes and size conventions, but the current product page is still the controlling record. A complete kit part number may contain several separately sold components. Verify whether the RoveSpec listing is a complete mount, holder with ball, arm only, base only, or adapter plate.

• Inspect behind drill-down surfaces for wiring, plumbing, controls, tanks, and structural members.
• Use backing and corrosion-compatible fasteners appropriate to the surface and environment.
• Seal penetrations in marine, exterior, and wet locations using the applicable vessel or vehicle practice.
• Keep devices outside airbag zones, driver sight-line restrictions, controls, and emergency exits.
• Hand-tighten ball-and-socket components as RAM directs and reassess ball size if the load will not hold.

• Do not adjust a device while operating a vehicle or vessel when doing so would be unsafe.
• Keep mounts clear of airbags, steering, throttles, shifters, switches, hatches, and escape paths.
• Remove or secure equipment before trailering, high-speed travel, or conditions beyond its stated use.
• Stop using components that slip, crack, deform, corrode, or no longer retain the device.
• Do not exceed the current RAM ball-size or product-specific load guidance.

• Check fasteners and backing for movement, corrosion, cracking, or water intrusion.
• Inspect rubber balls and socket surfaces for wear, contamination, heat damage, or loss of grip.
• Replace worn tethers, rubber caps, pads, springs, knobs, and other service parts with listed components.
• Rinse and dry marine installations as appropriate and isolate dissimilar metals.
• Recheck device fit after changing its case, battery, cable, or accessory.

The warranty applies to qualifying RAM mounts and components purchased through covered channels and is limited by the official conditions and claim procedure. Do not apply the mount warranty to a phone, tablet, fish finder, trolling motor, or other equipment attached to it.

• Device: make, model, dimensions with case, weight, ports, buttons, camera, stylus, and hole pattern
• Holder or plate: exact stated range or device pattern, retention method, tether, and ball interface
• Ball system: B, C, D, or other family on every component
• Arm: matching sockets, length, reach, leverage, knob access, and operating clearance
• Base: clamp range or drill pattern, surface material, thickness, backing, hardware, and sealing
• Environment: marine spray, vibration, wind, temperature, trailering, theft, and service access
• Commerce: current RoveSpec title, SKU, price, availability, selected variant, and product URL